Port of Mundra: India's Largest Private Port and the Philippine Manufacturing Case
Mundra moved the centre of gravity of Indian cargo. A private harbour on the Gulf of Kutch that became the country's largest commercial port, the first Indian port to pass 200 million tonnes in a single year, and one of only four notified Mega Ports in 2026. It is also the shortest reliable sea door between northern and western India and a Philippine factory floor. This page covers the harbour, then the two doors that open from it: investing in the Philippines and manufacturing there.
A private harbour that became a national gateway
Mundra sits on the north shore of the Gulf of Kutch in Kutch district, Gujarat, about 60 kilometres from Bhuj and roughly 400 kilometres from Ahmedabad. It began as a captive jetty for a salt and trading group in the 1990s and grew into an all weather, deep draft commercial port run by Adani Ports and Special Economic Zone Limited. Today it is the largest commercial port in India and the largest private one, and in September 2026 it was notified as a Mega Port under the Indian Ports Act 2025, the only non major port of the four.
What makes Mundra useful to a Philippine exporter or an Indian importer is not the headline tonnage. It is the combination. Mundra berths the largest container vessels afloat, sits on the main east west container corridor through the Arabian Sea, and evacuates boxes by rail into the northern hinterland on double stacked trains at a rate of up to 80 rakes a day. A container discharged at Mundra can be in Delhi NCR, Jaipur, Ludhiana or Ahmedabad before a Chennai box has finished its inland leg.
Three cargo families share the estate. Containers run through four terminals with a combined capacity of 7.5 million TEU. Crude arrives at two single point moorings that can take very large and ultra large crude carriers, then moves north by pipeline. Dry bulk, breakbulk, fertiliser, agri cargo and project loads use multipurpose berths with covered godowns for 7 lakh metric tonnes inside the port and another 3 lakh metric tonnes at the agri park, plus open yards of about 4 lakh square metres.
There is also a roll on roll off terminal in service since 2009, with a floating pontoon and link span that works without a tidal window, and an on site airport at Mundra that Adani Airports has been building out as a multimodal logistics hub. The airport runway is 900 metres today and is planned for expansion. For a first factory visit or a sample run, the practical air gateway is still Ahmedabad or Mumbai, then road.
- UN/LOCODE
- INMUN
- Location
- Mundra, Kutch district, Gujarat, north shore of the Gulf of Kutch
- Operator
- Adani Ports and Special Economic Zone Limited
- Berths
- 29 in total, 27 berths and 2 single point moorings
- Containers
- Four terminals, 7.5 million TEU combined capacity
- Draft
- 19 m at the mechanised import cargo berths, 17 m at the other berths
- Rail
- Connected to the national network, up to 80 rakes a day
- Road
- SH 48 via Anjar, SH 6 via Gandhidham, NH 8A
- Air
- Adani Mundra Airport on site, 900 m strip with expansion planned
- Liner services
- More than 35 services on global trade lanes
- Status
- Notified Mega Port, September 2026, under the Indian Ports Act 2025
Port particulars follow Adani Ports and the Ministry of Ports, Shipping and Waterways. Berth and terminal allocation changes with the vessel schedule, so confirm the terminal on the booking confirmation rather than on a planning page.
Mundra is one asset inside a much larger network
The port belongs to Adani Ports and Special Economic Zone Limited, which runs 15 domestic ports and terminals, four international ones, 12 multimodal logistics parks, about 3.1 million square feet of warehousing and a marine fleet of 136 vessels. That matters to a shipper because the same operator can move a box from a Philippine quay to a north Indian gate, and because a port dispute or congestion at one terminal can be absorbed elsewhere in the group.
Figures are the operator's reported FY26 results, year ended 31 March 2026.
Six working faces, one estate
A booking that says Mundra has named a port, not a terminal. The terminal decides the gate, the free time, the drayage cost and often the sailing itself. These are the six faces your forwarder will ask about.
Container terminals
Four container terminals with a combined capacity of 7.5 million TEU, served by rail mounted quay cranes and more than 35 liner services. The port groups its container handling into separate terminal codes, so the terminal number on your booking is the one to quote to the transporter.
Liquid terminal, MPT 1
Four dedicated liquid berths connected to a tank farm of 100 tanks holding 463,000 kilolitres, with 13 dock pipelines and 90 loading bays. It handles petroleum products, chemicals, edible oils and non edible oils, and it is the only terminal on the north west coast of India that handles bulk bitumen.
Single point moorings
Two offshore moorings that can take very large and ultra large crude carriers, feeding refineries in northern India through a cross country pipeline network. This is the crude engine of the port and it does not touch container cargo.
Dry bulk and breakbulk
Multipurpose berths for fertiliser, agri cargo, minerals, steel, timber and project loads, with grab ship unloaders and a mechanised bagging plant that can bag and load 25,000 tonnes of bulk fertiliser a day.
Roll on roll off
An automobile terminal in service since 2009, serving car, bus and truck exporters in Delhi NCR, Rajasthan and Gujarat, with a floating pontoon and link span that allows round the clock working without a tidal restriction.
Mundra airport and the industrial estate
The port has its own airport, positioned as a multimodal logistics and business hub, with a 900 metre strip and a plan to extend it. Around the harbour sits an industrial and special economic zone estate with power, utilities and warehousing, which is the reason a factory can be built beside the berth rather than a day away from it.
The reason Mundra wins is behind the quay
A Philippine container landing at Mundra is not competing with Chennai on berth productivity. It is competing on the cost of reaching the buyer. Mundra is the natural gateway for cargo clusters in northern and western India, and the cost advantage is structural rather than promotional.
Rail is the decisive advantage. Because the port is connected to the national network and runs its own rail operation, a box can be gated out of Mundra on the same day it is discharged and railed to an inland depot without a second handover. The port reports capacity for 80 rakes a day across inbound and outbound cargo, with separate sidings for agri, fertiliser, coal and liquid cargo, which keeps a container rake from queueing behind a coal rake.
Road access runs on two state highways, SH 48 via Anjar and SH 6 via Gandhidham, into NH 8A, the old Delhi to Kandla corridor. That is the routing a transporter will quote for Ahmedabad, Jaipur, Udaipur, Jodhpur, Ludhiana, Delhi NCR and the Noida and Gurugram clusters.
For an Indian buyer comparing west coast gateways, the practical comparison is Mundra against JNPA at Nhava Sheva. JNPA is closer to Mumbai and Pune. Mundra is the better answer for anything that has to reach Rajasthan, Gujarat, Punjab, Haryana, Delhi NCR or Madhya Pradesh, because the rail leg is shorter and the terminal is less congested on peak weeks.
What this means for a Philippine shipment
- Northern India
- Mundra is the default. Rail to an inland depot, then road to the buyer gate. Best for apparel, home textiles, electronics and auto parts headed to Delhi NCR, Punjab, Haryana and Rajasthan.
- Western India
- Mundra competes directly with JNPA. For Gujarat and Rajasthan it usually wins on cost. For Mumbai and Pune, JNPA is often cheaper once drayage is counted.
- Southern and eastern India
- Chennai, Cochin, Krishnapatnam and Kolkata are the shorter answer. Do not force a Mundra routing onto a Bengaluru or Hyderabad buyer without a landed cost comparison.
Clearance on the Indian side, in five checks
Indian import clearance runs electronically through ICEGATE, and the declaration is rarely the bottleneck. The delays sit in classification, origin proof and product certification. Settle those three before the vessel sails and Mundra becomes a short stop rather than a storage bill.
Qualify the importer of record
The Indian buyer needs a valid Importer Exporter Code from the Directorate General of Foreign Trade. The bill of entry is filed in that entity name, so a group buying through a sister company cannot clear on the parent code.
Fix the classification and the duty stack
Confirm the eight digit tariff line with a licensed customs broker before quoting. Apparel in HS Chapters 61 and 62 is a useful example of how the stack compounds: 20 percent basic customs duty, a 4 percent agriculture cess charged on the duty, a social welfare surcharge of 10 percent on duty and cess, and integrated tax at 5 or 18 percent depending on per piece value. At the 18 percent slab the headline is about 49.15 percent of CIF, and the irrecoverable part once the tax is credited is about 26.4 percent of CIF.
Claim the ASEAN India preference, not a guess
The Philippines has been a party to the ASEAN India Trade in Goods Agreement since 17 March 2016. A shipment backed by a Form AI certificate of origin can claim the preferential basic duty rate instead of the standard band, under Customs Notification 46 of 2011 as amended and the origin rules notified under CAROTAR 2020. The binding test is 35 percent AIFTA content by free on board value with the final manufacturing process inside a party. A bilateral Philippines India preferential trade agreement is still under negotiation and does not apply yet.
File the bill of entry and pay
A licensed customs broker files the bill of entry on ICEGATE, the customs assesses value and duty, the consignment is examined or scanned, duty and integrated tax are paid, and the out of charge order releases the container. Most of the elapsed time is the gap between arrival and a complete document set, not the assessment itself.
Clear product compliance before arrival
Regulated goods need Indian approvals arranged in advance: BIS registration for notified electronics and many consumer goods, FSSAI for food, CDSCO for drugs, cosmetics and medical devices, and legal metrology labelling for pre packaged goods. Textiles carry labelling requirements for fibre content and country of origin. Certification is arranged before the vessel berths, never at the gate.
| Document | Who issues it | What it unlocks |
|---|---|---|
| Form AI certificate of origin | Philippine authorised issuing body, under the ASEAN India framework | The preferential basic duty rate under the ASEAN India Trade in Goods Agreement |
| Importer Exporter Code | Directorate General of Foreign Trade | The right to import and to be named as importer of record |
| Bill of lading | Carrier or freight forwarder | Release of the container and the basis of the bill of entry |
| Commercial invoice and packing list | Exporter | Customs valuation, duty base and warehouse receipt |
| Bill of entry | Licensed customs broker through ICEGATE | Assessment, examination, duty payment and out of charge |
| BIS, FSSAI or CDSCO approval | The relevant Indian regulator | Release of regulated electronics, food, drugs, cosmetics and devices |
| Insurance certificate | Exporter or buyer, depending on the Incoterm | Cargo cover and a clean document set for the bank |
The three routes from a Philippine quay to Mundra
Mundra sits at the top of the 7 to 18 day India planning band on our India trade page, because a west coast call usually relays at Colombo, Singapore or Port Klang before the Arabian Sea leg. Treat the booking confirmation as the only transit figure that counts.
- Sea, full container
- 20 foot and 40 foot boxes, port to port, with the west coast relay built into the planning band.
- Sea, consolidated
- Less than container loads consolidated at Singapore or Port Klang, suited to trial orders and mixed cartons.
- Air freight
- Manila or Cebu to Ahmedabad or Mumbai, then road to Kutch or the buyer inland depot. Mundra airport is not yet the international cargo answer.
- Courier and hand carry
- Sample runs and urgent replacements, cleared as express consignment or accompanied baggage.
Philippine origins and what each is best for
- Manila, MICT and South Harbor. The deepest carrier choice and the most frequent sailings, and the default origin for Luzon factories and consolidated apparel orders.
- Cebu International Port. Visayas production, with steady container calls and a useful midpoint for mixed Philippine sourcing.
- Davao, Sasa and DICT. Mindanao volume, including the Davao Region apparel and agricultural base, and usually the longest sea leg.
- Batangas and Subic. Southern and central Luzon alternatives that relieve Manila yard pressure at peak season, with bonded storage at Subic before export.
Invest where the ownership rules and the tax rate both work
India and the Philippines traded 3.9 billion US dollars in the 2025 to 2026 financial year, up from 3.34 billion the year before. India sells engineering goods, pharmaceuticals, vehicles and rice. The Philippines sells semiconductors, electrical machinery, copper, ores and precious stones. That is a trade relationship moving in both directions, and it is why the 14th Joint Working Group on Trade and Investment, meeting in Manila in June 2026, put film, energy, construction and infrastructure, ICT, IT enabled services and artificial intelligence, and pharmaceuticals on the cooperation list.
On the rules, the ASEAN India Trade in Goods Agreement review is being pushed to an early conclusion, with a bilateral Philippines India preferential trade agreement to follow. Neither is signed. What already exists is a Philippine investment regime that an Indian promoter can use today, and it is unusually open.
| Instrument | What it gives |
|---|---|
| CREATE MORE, RA 12066 | A 20 percent corporate income tax for registered enterprises, a 4 to 7 year income tax holiday, and a 10 or 20 year special regime. High value projects can reach 27 years. |
| Foreign Investments Act, RA 11647 | Up to 100 percent foreign ownership in most sectors, with a short negative list of restricted activities. |
| PEZA registration | Export manufacturing inside an ecozone, with tax holidays, zero rated local purchases and simplified customs. The zone system covers 441 ecozones and more than 4,400 locator firms. |
| Board of Investments | Fiscal and non fiscal incentives for preferred sectors, including duty free capital equipment and enhanced deductions. Approvals reached ₱900.06 billion from January to September 2026, up 53 percent across 207 projects. |
| Investors' Lease Act, RA 7652 | Private land leases of 50 years, renewable for 25 more, which removes the land tenure objection for factories and estates. |
| PEZA performance | ₱309.63 billion registered from January to October 2026, across ecozones that together produce about 13 percent of national output. |
Registration with PEZA or the Board of Investments comes first and the incentive package follows the registration. Confirm the exact activity against the current Foreign Investment Negative List before signing a joint venture, because the list changes.
Manufacture where the labour, the English and the shipping line all line up
Gujarat runs on petrochemicals, refining, chemicals, textiles, ceramics, pharmaceuticals and ports. The Philippines complements that base rather than competing with it. It offers a young, English speaking workforce, a legal system built on United States commercial practice, ecozones with their own customs administration, and a Pacific position that reaches the United States and Japan faster than any Indian factory can.
For an Indian manufacturer, the interesting move is not moving the plant. It is adding a second production address that sells into markets where India pays a tariff or a freight penalty. Electronics alone shipped 49.64 billion US dollars from the Philippines in 2025, 59.3 percent of merchandise exports, with a 2026 forecast of 53 to 54 billion dollars.
- Electronics and board assembly. Philippine electronics manufacturing services already serve global original equipment makers. An Indian component maker can place board assembly or box build in a PEZA zone and ship finished product into the United States and Japan without the Indian freight and duty position.
- Pharmaceuticals and medical devices. Indian generics strength pairs with Philippine packaging, device assembly and clinical support services. The Joint Working Group named pharmaceuticals explicitly, and CDSCO and Philippine FDA approvals are the gating items.
- Automotive parts and wiring. Philippine suppliers make harnesses, interiors and precision plastics for Japanese and American assemblers. An Indian tier one can use that base for regional supply into ASEAN rather than shipping from Pune or Chennai.
- IT, IT enabled services and AI. The same Joint Working Group listed ICT, IT enabled services and artificial intelligence. Philippine delivery centres serve United States time zones, which is a capability an Indian provider cannot replicate from Bengaluru.
- Apparel, workwear and uniforms. The Philippine garment sector runs on small and medium order sizes with short lead times, which suits corporate uniforms, workwear and branded merchandise rather than mass commodity knitwear. Fabric imported from India can be cut and sewn in a PEZA zone, and the origin arithmetic has to be costed before the order is quoted.
Power and inland logistics are material line items. Model the ecozone to port drayage and the electricity tariff before you model the wage saving. Site selection support covers the Davao Region, CALABARZON and the Clark and Subic corridor.
What Indian buyers ask first
These arrive in the first call, usually in this order.
What is the UN/LOCODE for the Port of Mundra?
INMUN. The port sits at roughly 22 degrees 44 minutes north and 069 degrees 47 minutes east, on the north shore of the Gulf of Kutch in Kutch district, Gujarat. It is not the same location as Kandla, which is a separate port further north in the same gulf.
How long does sea freight take from the Philippines to Mundra?
Mundra sits at the top of the 7 to 18 day India planning band, because most west coast services relay at Colombo, Singapore or Port Klang before the Arabian Sea leg. Customs clearance, transshipment and inland rail add time. Treat the booking confirmation as the only transit figure that counts.
Which terminal will my container discharge at in Mundra?
Mundra runs four container terminals with a combined capacity of 7.5 million TEU, plus separate liquid, dry bulk, breakbulk and roll on roll off facilities. The terminal code is on the booking confirmation and it decides the gate and the drayage cost, so quote that code to the transporter rather than the port name alone.
Is Mundra or Nhava Sheva better for a Philippine shipment into north India?
Mundra for Delhi NCR, Punjab, Haryana, Rajasthan, Gujarat and Madhya Pradesh, because the rail leg is shorter and the terminal is less congested at peak. Nhava Sheva, which is JNPA, is usually better for Mumbai and Pune. Run a landed cost comparison that includes rail, drayage, free time and the sailing schedule before deciding.
Does the Philippines get a preferential duty rate into India?
Yes, under the ASEAN India Trade in Goods Agreement, which the Philippines has been party to since 17 March 2016. A Form AI certificate of origin claims the preferential basic duty rate under Customs Notification 46 of 2011 as amended, with origin rules under CAROTAR 2020. The binding test is 35 percent AIFTA content by free on board value with the final manufacturing process inside a party. A bilateral Philippines India preferential trade agreement is still under negotiation.
What duty does apparel from the Philippines pay into India?
Knitwear and woven apparel in Chapters 61 and 62 typically carry a 20 percent basic customs duty, plus a 4 percent agriculture cess charged on the duty, plus a social welfare surcharge of 10 percent on duty and cess, plus integrated goods and services tax at 5 or 18 percent depending on per piece value. At the 18 percent slab the headline is about 49.15 percent of CIF, and the irrecoverable part once the tax is credited is about 26.4 percent of CIF. A Form AI certificate lowers the basic duty rate, so confirm the exact line with a licensed broker.
Can an Indian company own 100 percent of a Philippine factory?
In most sectors, yes, under the Foreign Investments Act. A short negative list still sets ownership ceilings for specific activities and the list changes, so confirm the exact activity against the current Foreign Investment Negative List before signing a joint venture.
Can PHShirt ship apparel from the Philippines to Mundra?
Yes. We quote FOB Manila, Cebu or Davao and CIF Mundra, Nhava Sheva or Chennai, with the Form AI documentation needed for the ASEAN India preferential rate where the origin test is met. Production lead time and transit are quoted together so the landing date is visible before the order is confirmed.
The corridor in more detail
Mundra is one node. These pages cover the country case, the competing gateways and the service side.
Talk to the export desk about Mundra
Production enquiries, sample requests, freight planning and site visits in the Davao Region. We answer in English and can walk an Indian buyer or promoter through the origin calculation before the first order.
Mon to Sat, 8:30 AM to 5:00 PM (PHT). Naungayan Building, Aala Road, Barangay Mankilam, Tagum City, Davao del Norte, Philippines.
